NDT Technology

NDT Technology

Development of an Ultrasonic Testing Method for B-Scan Detection of Notch in Polymer Additively Manufactured Components

Document Type : Original Article

Authors
1 Department of mechanical Engineering, K. N. Toosi university of technology, Tehran, Iran.
2 Department of Aerospace Engineering, The Shahid Sattari University of Aeronautical Engineering, Tehran, Iran.
Abstract
Additive manufacturing (AM) is an emerging manufacturing technology in which components are fabricated layer by layer. Among the various additive manufacturing techniques, polymer material extrusion is one of the most widely used processes for producing polymer components. Despite the numerous advantages of this process, the occurrence of defects during manufacturing is inevitable. Therefore, the assessment and monitoring of component integrity, including the determination of material properties and the detection of common defects, still require further investigation. In addition, the development of evaluation methods for nondestructive testing systems specifically designed for AM polymer components is of considerable importance. In this study, a mechanized B-scan system was designed and developed to establish an ultrasonic testing method for the evaluation of polymer components. First, the ultrasonic wave velocity in the components was measured to determine the accurate location of defects based on the measured acoustic properties. The ultrasonic wave velocity was measured as 2165 m/s, with a measurement error of less than 1%, indicating a high level of measurement accuracy. Then, the notch defect in the standard V1 calibration block was used as a reference for designing artificial notches in AM polymer components. In this way, the artificial defects introduced during the fabrication of the components can be represented by notches equivalent to those in the reference calibration block, thereby providing reference defects for evaluating the ultrasonic inspection capability of AM polymer components. Subsequently, the performance of the ultrasonic probes and their resolution capability were evaluated according to the characteristics of the reference block. Ultrasonic tests were then performed using both contact and immersion techniques to compare and validate the two methods. Finally, the performance of the immersion B-scan method was evaluated for locating notches with different dimensions, and an appropriate linear scanning speed in the range of 16–24 mm/min, with an average value of 20 mm/min, was determined as the optimal operating range of the developed system.
Keywords
Subjects

[1] Honarvar, F., & Varvani-Farahani, A. (2020). A review of ultrasonic testing applications in additive manufacturing: Defect evaluation, material characterization, and process control. Ultrasonics, 108, 106227.
[2] Riahi, M., & Javidrad, H. R. (2020). Production of ultrasonic test piece by utilization of additive manufacturing technique. Russian Journal of Nondestructive Testing, 56(10), 843-852.
[3] Riahi, M., & Javidrad, H. (2021). Utilization of Special Characteristics in the Manufacturing of Additive Manufacturing Parts for Precise Calibration of Ultrasonic Test Equipment. NDT Technology, 2(8), 27-40. (in persian)
[4] Fayazbakhsh, K., Honarvar, F., Amini, H., & Varvani-Farahani, A. J. A. M. (2021). High frequency phased array ultrasonic testing of thermoplastic tensile specimens manufactured by fused filament fabrication with embedded defects. Additive Manufacturing, 47, 102335.
[5] Zeltmann, S. E., Gupta, N., Tsoutsos, N. G., Maniatakos, M., Rajendran, J., & Karri, R. (2016). Manufacturing and security challenges in 3D printing. Jom, 68(7), 1872-1881.
[6] Grozdanić, M., Mihaljević, M., Cajner, H., & Godec, D. (2025). Influence of layer thickness and disc orientation on additively manufactured disc-shaped reflectors for ultrasonic testing. Journal of nondestructive evaluation, 44(2), 60.
 [7] Eyer, P., Enzler, S., Trauth, A., & Weidenmann, K. A. (2024). Investigating the mechanical properties of polymer samples from different additive manufacturing processes using ultrasonic phase spectroscopy. 3D Printing and Additive Manufacturing, 11(2), 666-674.
[8] Chabot, A., Laroche, N., Carcreff, E., Rauch, M., & Hascoët, J. Y. (2020). Towards defect monitoring for metallic additive manufacturing components using phased array ultrasonic testing. Journal of Intelligent Manufacturing, 31(5), 1191-1201.
[9] Taheri, H., Koester, L. W., Bigelow, T. A., Faierson, E. J., & Bond, L. J. (2019). In situ additive manufacturing process monitoring with an acoustic technique: clustering performance evaluation using K-means algorithm. Journal of Manufacturing Science and Engineering, 141(4), 041011.
[10] Soleymani, A., & Riahi, M. (2024). Investigating Non-destructive Tests Used in the Inspection of Parts Produced by Additive Manufacturing (AM) Method. NDT Technology, 3(3), 108-123. (in persian)
 [11] ASTM International. (2023). Additive Manufacturing of Metals—Nondestructive Testing and Evaluation—Defect Detection in Parts. ASTM International.
[12] Bagheri-Bami, A., & Honarvar, F. (2022). Determination of the type of anisotropy and stiffness tensor in additive manufacturing polymer components by using ultrasonic waves. Iranian Journal of Manufacturing Engineering, 9(6), 36-48. (in persian)
[13] Cummings, I., Hillstrom, E., Newton, R., Flynn, E., & Wachtor, A. (2016, May). In-process ultrasonic inspection of additive manufactured parts. In Topics in Modal Analysis & Testing, Volume 10: Proceedings of the 34th IMAC, A Conference and Exposition on Structural Dynamics 2016 (pp. 235-247). Cham: Springer International Publishing.
[14] Oliveira, T. F. D., Cavalheiro, A. C. M., Tsuzuki, M. D. S. G., Buiochi, F., Leão Neto, P., Silva, G. C. D., ... & Andrade, J. H. L. D. (2025). Ultrasonic characterization of 3D-printed polymer objects. Ultrasonics, 149, 1-11.
[15] Chen, Y., Peng, X., Kong, L., Dong, G., Remani, A., & Leach, R. (2021). Defect inspection technologies for additive manufacturing. International Journal of Extreme Manufacturing, 3(2), 022002.
[16] Lee, J., Hasanian, M., Saboonchi, H., Baechle, M., & Taheri, H. (2020, April). Ultrasonic evaluation of polymer additively manufactured parts for defect inspection and structural integrity assessment. In Nondestructive Characterization and Monitoring of Advanced Materials, Aerospace, Civil Infrastructure, and Transportation XIV (Vol. 11380, pp. 260-270). SPIE.
[17] Zimermann, R., Mohseni, E., Vithanage, R. K., Lines, D., Foster, E., Macleod, C. N., ... & Ding, J. (2022). Increasing the speed of automated ultrasonic inspection of as-built additive manufacturing components by the adoption of virtual source aperture. Materials & Design, 220, 110822.
[18] Jiang, L., Chen, Y., Cao, J., Li, Y., Ye, Y., Zhang, J., ... & Yan, J. (2026). A laser–piezo hybrid ultrasonic focusing method based on diffracted shear waves for detection of embedded defects in metal additive manufacturing. Measurement Science and Technology, 37(2), 025202.
 [19] R.Shabani, F. Honarvar, Variation of Longitudinal Ultrasonic Wave Velocity in the Presence of Thermal Gradient; Part 2: Experimental Study and Uncertainty Analysis,
Modares Mechanical Engineering, Vol. 16, No. 4, pp. 10-16, 2016. (in Persian)

  • Receive Date 18 July 2026
  • Revise Date 16 September 2026
  • Accept Date 04 October 2026